board_home 

Visit the
UK MOT Testing
Industry Portal



 Moderated by: Stealth, MOTman, martins, KevG, bimmer
New Topic Reply Printer Friendly
ntt  Rate Topic 
AuthorPost
 Posted: Sat Aug 7th, 2010 08:45 pm
  PM Quote Reply
1st Post
bimmer
Moderator


Joined: Fri Sep 4th, 2009
Location: United Kingdom
Posts: 763
Status: 
Offline
Mana: 
in my opinion there never were any answers to confirm which is why i said what i said .:P

Back To Top PM Quote Reply  

 Posted: Sat Aug 7th, 2010 08:12 am
  PM Quote Reply
2nd Post
garage express
Trade Member
 

Joined: Mon Mar 8th, 2010
Location: London, United Kingdom
Posts: 24
Status: 
Offline
Mana: 
What would you learn by the answers being put on here from me as bimmer mentioned you post the answers and then we can see what you have put. May i remind you that the questions of 5 you need 3 right in each catergory and the 10 you need 7 but you must get at least 1 more that that right to achieve a pass.

Back To Top PM Quote Reply

 Posted: Fri Aug 6th, 2010 05:03 pm
  PM Quote Reply
3rd Post
bimmer
Moderator


Joined: Fri Sep 4th, 2009
Location: United Kingdom
Posts: 763
Status: 
Offline
Mana: 
it would be simpler for you to post your answers and then we can check them. ;)

Back To Top PM Quote Reply  

 Posted: Fri Aug 6th, 2010 04:18 pm
  PM Quote Reply
4th Post
jay_kay
Member
 

Joined: Fri Jul 30th, 2010
Location:  
Posts: 4
Status: 
Offline
Mana: 
oh a bit cheeky but would you happen to have the answrs to these questions jut to confirm mine

Back To Top PM Quote Reply

 Posted: Wed Aug 4th, 2010 04:26 pm
  PM Quote Reply
5th Post
jay_kay
Member
 

Joined: Fri Jul 30th, 2010
Location:  
Posts: 4
Status: 
Offline
Mana: 
thanks :)

Back To Top PM Quote Reply  

 Posted: Tue Aug 3rd, 2010 10:36 am
  PM Quote Reply
6th Post
garage express
Trade Member
 

Joined: Mon Mar 8th, 2010
Location: London, United Kingdom
Posts: 24
Status: 
Offline
Mana: 

NTTA Sample Questions


Brakes


1. How would you check that a hydraulic braking system vacuum servo is assisting foot brake pedal effort ?


A = listen for a change in engine speed when applying the foot brake.


B = measure the brake application time lag.


C = feel for an increase in brake pedal movement as the servo vacuum builds up after being emptied.


D = look for a change in the brake fluid reservoir level when the foot brake is applied.


2. Which one of the following foot brake efficiency ranges should a properly maintained modern four wheeled car


be expected to achieve in an EMERGENCY BRAKING situation on a dry tarmac road ?


A = 100% to 105%


B = 80% to 85%


C = 50% to 55%


D = 25% to 30% 3.


3. A car is accidentally fitted with O/S/F wheel cylinders that have pistons 2.0mm GREATER in DIAMETER than


the N/S/F wheel cylinders pistons. This is likely to cause ?


A = excessive brake bind at the O/S


B = the brakes to pull to the O/S


C = the brakes to pull to the N/S


D = no difference in the braking


4. What causes 'sponginess' in a hydraulic braking system ?


A = air in the hydraulic fluid


B = partially seized wheel cylinders


C = new unused brake discs


D = excessive play in wheel bearings


5. Which one of the following is true about hydraulic brake fluid ?


A = it is always a red colour


B = it repels water


C = it freezes at approximately 0 degrees C


D = it absorbs water


6. Hydraulic brake fluid ?


A = compresses very easily


B = expands considerably when heated


C = is virtually incompressible


D = contracts considerably when cooled


7. Which one of the following is NOT a type of disc brake calliper ?


A = sliding


B = swinging


C = expanding


D = twin piston


8. Which one of the following is true ?


A = brake linings are always riveted to brake shoes


B = brake linings are always bonded to brake shoes


C = brake linings can absorb oil


D = brake linings cannot absorb oil


9. Excessive brake disc 'run-out' indicates that a brake disc is ?


A = buckled


B = not circular


C = too small


D = worn thin


10. Which one of the following does NOT change the braking effectiveness of a car ?


A = wheel cylinder piston length


B = wheel cylinder piston diameter


C = brake pedal pressure


D = brake linings or disc pads hardness


Steering


11. A track control arm is for ?


A = reducing body roll


B = locating the position of a road wheel


C = providing the means for adjusting toe in/out


D = adjusting camber angle


12. What is steering castor ?


A = a steering joint lubricant


B = a front hub grease slinger


C = a steering geometry feature


D = a constant velocity joint component


13. The camber angle setting of a road wheel determines ?


A = the plane of a road wheel in relation to the vertical


B = The wheel bearing type


C = the maximum amount that the steering can be turned towards locks


D = the maximum rebound action


14. Steering self centring (or self righting) is mainly produced by ?


A = king pin inclination


B = toe in or toe out


C = camber


D = castor


15. Which unit is a sector shaft a part of ?


A = rack and pinion assembly


B = steering box assembly


C = power steering pump assembly


D = Steering idler assembly


16. Which force is a steering column most subjected to in normal use ?


A = torsion


B = sheer


C = bending


D = compression


17. Which one of the following determines the amount of steering 'toe out' (Ackerman effect) on locks ?


A = steering arm to stub axle angle


B = castor


C = rack and pinion gear ratio


D = drop arm length


18. What is meant by the term ' over steer ' ?


A = the tendency for a vehicle to steer on a smaller turning circle than is expected


B = the steering wheel is situated in front of the first axle


C = the steering wheel is situated directly over the first axle


D = the tendency for a vehicle to steer on a larger turning circle than is expected


19. Steered wheels tracking adjustment is normally made by ?


A = fitting a different length drag link


B = adjusting suspension link arms


C = adjusting steering column end float


D = adjusting track rod length


20. If a steering power assistance pump stops working it will cause ?


A = total loss of steering control


B = restricted steering towards locks


C = the steering to feel heavy


D = the steering to feel light


Suspension


21. A transverse leaf spring is one which has its greatest length ?


A = in line with the length of the vehicle


B = across the vehicle


C = to the front of the driving axle


D = to the rear of the driving axle


22. A leaf spring 'swinging shackle' is for ?


A = securing the spring to the axle


B = preventing the spring leaves from splaying


C = limiting the spring thickness


D = allowing the spring to alter its effective length when flexing


23. A suspension bump stop is for ?


A = securing spring 'U' bolts


B = limiting suspension vertical movement


C = limiting suspension lateral movement


D = reducing road wheel vibration


24. Which type of shock absorber (damper) is usually used with a MacPherson strut suspension ?


A = lever


B = friction


C = telescopic


D = hydrolastic


25. The eye of a leaf spring is for ?


A = locating the spring on an axle


B = attaching a spring to a chassis or body


C = attaching a shock absorber (damper) to the spring


D = checking spring alignment


26. A suspension torsion bar is usually made from ?


A = mild steel


B = spring steel


C = silver steel


D = cast iron


27. When a suspension coil spring is 'coil bound' it usually indicates that ?


A = the spring is over loaded


B = the spring is encased in a weatherproof jacket


C = the vehicle weight has been reduced


D = the vehicle has the wrong wheel clearance


28. What fluid is normally in hydraulic shock absorbers (dampers) ?


A = water


B = a water / anti-freeze mixture


C = alcohol


D = oil


29. In which direction does a 'panhard rod' control suspension movement in relation to a vehicle longitudinal axis ?


A = laterally


B = vertically


C = towards the front


D = towards the rear


30. Which one of the following front suspension system must have TWO combined steering & suspension swivel


joints and TWO pivot joints for EACH front wheel ?


A = MacPherson strut


B = semi-elliptic leaf


C = double wishbone


D = leading arm


Wheels and Tyres


31. Which types of tyre construction have the most flexible side walls ?


A = cross ply


B = bias belted


C = radial


D = cross ply remoulds


32. What does a tyre 'ply rating' indicate ?


A = load carrying capacity


B = inflation pressure


C = maximum safe road speed


D = tread rubber thickness


33. The correct wheel rim diameter for a 185 x 13 size tyre is ?


A = 13cm


B = 185mm


C = 13 inches


D = 6.5 inches


34. Where on a tyre are tread wear indicators located ?


A = in the tread


B = on the side wall


C = on each shoulder


D = at the bead


35. A tyre that is run under inflated will wear more rapidly ?


A = at the tread centre


B = on the outer side wall


C = at the tread shoulders


D = on the inner side wall


Wheels and Tyres


36. What is the approximate voltage produced from ONE CELL of a Lead / Acid battery ?


A = 2 volts


B = 4 volts


C = 6 volts


D = 12 volts


37. What minimum fuse rating is needed for a 12 volt circuit with just one 48 watt bulb ?


A = 0.4 Amp


B = 2.0 Amp


C = 3.0 Amp


D = 4.0 Amp


38. For vehicle wiring, the expression "Earth Return" means ?


A = the circuit earths to ground via the vehicle wheels or an earth strap


B = all circuits must have over load cut-out switches


C = relays are needed on all circuits


D = the vehicle body or chassis is a part of the circuit


39. The beam image pattern emitted by some modern headlamps is determined by ?


A = its lens


B = the supply voltage


C = the circuit amperage


D = its height from the ground


40. An alternator has a diode rectifier for ?


A = boosting voltage


B = cooling


C = converting output to AC


D = converting output to DC


Body & Corrosion


41. The corrosion process of steel car bodies is known as ?


A = oxidation


B = carbonisation


C = ionisation


D = hydration


42. Steel car bodies can be protected from corrosion by ?


A = galvanising


B = tempering


C = normalising


D = annealing


43. Which metal is most resistant to rusting ?


A = iron


B = high carbon steel


C = low carbon steel


D = stainless steel


44. The corrosion of mild steel is increased by the addition of ?


A = alcohol


B = oil


C = nitrogen


D = salt


45. The evidence of corrosion on aluminium and its alloys is seen on the metal as ?


A = a red stain


B = a white powder


C = a brown stain


D = a brown powder


Exhaust Emissions


46. When a petrol engine is running rich the exhaust gas hydrocarbon (HC) will be ?


A = higher than it should be


B = lower than it should be


C = the same as when the engine is running weak


D = the same as the exhaust gas carbon monoxide content


47. Petrol is mainly composed of ?


A = nitrogen and oxygen


B = oxygen and hydrogen


C = oxygen and carbon


D = carbon and hydrogen


48. The colour of the exhaust gas emitted from a petrol engine that is running very rich is likely to be?


A = black


B = white


C = dark blue


D = light blue


49. A 4 cylinder petrol engine has an exhaust gas hydrocarbon content of 600 ppm (parts per million). What is the


hydrocarbon content likely to be when a plug lead is removed ?


A = over 900 ppm


B = 600 ppm


C = 500 ppm


D = under 400 ppm


50. The CO (carbon monoxide) content of the exhaust gas emitted from a properly maintained non-cat 4 cylinder


petrol engine in good condition is most likely to be ?


A = 3.0%


B = 9.0%


C = 12.0%


D = 15.0%


Exhaust Emissions


51. Which one of the following petrol / air mixtures is closest to the theoretical best for the most complete


combustion in a petrol engine ?


A = 20 air units to 1 petrol unit


B = 15 air units to 1 petrol unit


C = 20 petrol units to 1 air unit


D = 15 petrol units to 1 air unit


52. Which one of the following fuels should be used when there is a catalytic converter in the exhaust system ?


A = 100 octane petrol having 1.4% Tetraethyl-lead


B = 92 octane petrol having 0.4% Tetraethyl-lead


C = 92 octane petrol without any Tetraethyl-lead


D = a blend of 85 octane petrol and paraffin


53. Which one of the following situations is the correct one for measuring the normal 'in use' exhaust emissions


from a petrol engine ?


A = when the engine is cold


B = when the engine coolant water is hot and the sump oil is still cool


C = when the engine coolant water and sump oil are both at normal working temperature


D = when the air cleaner is removed and both the sump oil and engine water coolant are at working temperature


54. Which is the correct procedure when using an exhaust gas analyser for determining the exhaust emissions


from a V6 petrol engine that has two totally separate exhaust systems ?


A = add together the readings from each tail pipe


B = average the readings from the tail pipes


C = take the readings from only one tail pipe


D = multiply together the readings from each tail pipe


55. Which element in the atmosphere aids combustion ?


A = Nitrogen


B = Carbon dioxide


C = Carbon monoxide


D = Oxygen


General


56. An exhaust system expansion box is for ?


A = removing harmful gases


B = reducing exhaust noise


C = controlling hydrocarbon emissions


D = controlling carbon monoxide emissions


57. A petrol engine exhaust system catalytic converter is for ?


A = removing certain harmful exhaust emissions


B = condensing steam to water


C = extra silencing


D = preventing an exhaust system from over heating


58. An 'inertia reel' seat belt is one which ?


A = unwinds to allow body movement in a head-on collision


B = locks to restrict body movement in a head-on collision


C = is only fitted with lap type seat belts


D = is only fitted with full harness type seat belts


59. A 'lap' type seat belt is one which ?


A = has a 3 point mounting


B = has a single point mounting


C = has a 2 point mounting


D = does not need a mounting


60. Which type of windscreen will crack without shattering ?


A = toughened


B = laminated


C = tinted


D = wrap around

Back To Top PM Quote Reply

 Posted: Fri Jul 30th, 2010 01:49 pm
  PM Quote Reply
7th Post
jay_kay
Member
 

Joined: Fri Jul 30th, 2010
Location:  
Posts: 4
Status: 
Offline
Mana: 
hi am goin to take my NTT exam very soon. was tinking if a can get questions and anwers fron anyway. any suggesions please help!!!!!!! thanks

Back To Top PM Quote Reply  

 Posted: Mon Feb 22nd, 2010 09:05 pm
  PM Quote Reply
8th Post
seymour beaver
Member
 

Joined: Mon Feb 22nd, 2010
Location: United Kingdom
Posts: 1
Status: 
Offline
Mana: 
How did it go?

Back To Top PM Quote Reply

 Posted: Fri Feb 12th, 2010 08:17 pm
  PM Quote Reply
9th Post
dennis
Member
 

Joined: Wed Feb 3rd, 2010
Location: United Kingdom
Posts: 4
Status: 
Offline
Mana: 
thanks :D

Back To Top PM Quote Reply  

 Posted: Thu Feb 4th, 2010 11:19 am
  PM Quote Reply
10th Post
bimmer
Moderator


Joined: Fri Sep 4th, 2009
Location: United Kingdom
Posts: 763
Status: 
Offline
Mana: 
good luck on your test dennis, and enjoy the forum.

Back To Top PM Quote Reply

 Posted: Wed Feb 3rd, 2010 11:09 pm
  PM Quote Reply
11th Post
Wesley
Trade Member
 

Joined: Tue Sep 25th, 2007
Location: Wanted
Posts: 1841
Status: 
Offline
Mana: 
Hi Dennis,

Have a look on the http://www.vosa.gov.uk website.

Back To Top PM Quote Reply  

 Posted: Wed Feb 3rd, 2010 06:40 pm
  PM Quote Reply
12th Post
dennis
Member
 

Joined: Wed Feb 3rd, 2010
Location: United Kingdom
Posts: 4
Status: 
Offline
Mana: 
hi i am shortley going to sit my ntt test. i have been studdying hilliers some time now and have worked in the motor trade as a machanic for over five year. could anybody help me with more sample questions other than the ones provided thanks :D  email denr2009@hotmail.co.uk

Last edited on Wed Feb 3rd, 2010 07:34 pm by dennis

Back To Top PM Quote Reply

Current time is 02:11 pm  
MOT Forum - The MOT Testing Forum for the UK MOT Testing Industry > Trade Category (MOT Trade Discussions) > MOT Regulations - Need clarification? try here | MOT Forum > ntt Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems